Seedlings require a medium amount of light in which it has enough to grow but not too much light that it gets burned. Leaving your seedling in direct sunlight will cause the leaves to curl, while too little light will cause the seedling to stretch. If growing outside, seedlings want to see a direct light source to stop them stretching. If inside, a sunny windowsill with more than half a day of sunlight works wonders. Otherwise, 18 in away from a growing light works excellently. Your seedling should not stretch more than 6 in at most. We’ll cover lighting in more depth in a later blog.
Starting from seed is a remarkable journey. Understanding the biology is one thing, but comprehending how a little miracle bean can turn into a gigantic tree that can affect your body and mind is nothing short of an evolutionary miracle. Or rather a co-evolutionary story of plant and human.
Our favorite thing about starting from a seed, rather than a clone, is that you get to see the full life cycle and enjoy a plant that is unique, just like you. An entirely new genetic makeup will enter the world for the first time, and if you’re lucky, something remarkable might be born.
4) Lighting for your seedling
We like to use seedling pellets that are made of a mix of compressed peat moss and coco husk. To expand, soak it in water for 10 minutes. Once your seedling pellet has absorbed enough water and has expanded to its maximum size, drain off any excess water. The growing medium should be like a damp sponge that would not leave streaks on the table. Dig a small hole about 1/4 in deep for your seed. Use a spoon to lift the seed out of its bath. If it has popped out a taproot be careful not to damage it. Gently place the seed into the hole and lightly cover it with dirt from the pellet. Now that you have started the germination process, your seedling will come above ground within two weeks. The older the seed, the longer it takes for it to germinate.
To accelerate germination, you are going to want to soak your seed in a small container with lukewarm water and place it in a dark and warm place for 12-24 hours, but no longer. By drenching the seed, it absorbs the water thoroughly, activating the germination process. Doing this also helps to loosen the shell as it becomes a little softer making it easier for the embryo to crack it open. When your seed sinks to the bottom it is ready to be planted, and sometimes the seed will pop out a small taproot. A seed can still be planted though if it does not sink.
For young plants, it’s best to use bottled water as it has no chlorine added. If using tap water, let it sit for 24 hours before watering to dissipate any chlorine. Chlorine can also be eliminated by boiling for 20 minutes. Under normal conditions, after soaking your seedling pellet, it should contain all the moisture your plant needs before it comes above ground. As it grows, it will only need about a shot glass worth of water at most per week to keep the medium damp. Seedlings don’t drink a lot of water, which makes sense given their size. Your plant will do better in a growing medium which is damp. Overwatering is just as deadly as drying out.
Perhaps the most exciting stage, your baby will typically come above ground in 1-2 weeks. As your seedling comes above the soil, its shell might take a few days to fall off. It’s best to leave it alone, nature has the job covered. If it does not come above ground after about two weeks, the chance of success is dramatically reduced, and it’s best to try again. Even the best seeds have an 85% germination rate. When your seedling comes above ground, it is going to want to see a direct light source.
Within a week or so you should see a seedling begin to grow from the soil.
If you’re ready for a more serious approach, make sure you have the space for a proper garden and pop the seeds to see what fruit they bear.
Because training happens during vegetative growth, for autoflowering plants, this period could be as short as a few weeks, which means time is limited. Try topping your autoflowers after they have three nodes, and stop once they begin to flower. You will want to prune them lightly.
Seeds found in finished cannabis buds can develop for a number of reasons. For example, a male plant may have accidentally pollinated a flowering female during the growing process. But more commonly, they’re a sign of stress and can be attributed to high temperatures during the final stages of flowering or an exaggerated spike in climate or environment.
Also, autoflower plants are small—perfect for closet grows or any small grow, or growing outdoors where you don’t want your neighbors to see what you’re up to.
Females will have a round structure with long hairs—these hairs will develop into pistils, which will catch pollen in the air.
There are a few indicators that will give you a sense of whether the seed is worth germinating.
HUMIDITY: Outdoors you don’t really have any control over this factor and you are at the mercy of your climate. The upside is that the variations in humidity and the robust biological functions needed to adapt to a changing grow environment makes your plants exceptionally strong!
Your plants are happy in an organic soil or they are being fed nutrients designed for the vegetative phase. Lots of fan-forced breezes keep temperatures under control and strengthen your young plants. Exotic disciplines can be used like adding carbon dioxide to the environment. Low-stress training and scrogging can be used to increase the growth rate and flower potential of indoor cannabis.
Step 3: Lights For Indoor Cannabis Growing
GERMINATION STATIONS: Offering substantial control over the germinating environment germination stations provide humidity, temperature control and can accelerate germination times.
In order to grow at its best and give you the juicy buds, you love cannabis requires some fundamental things.
NUTRIENTS: Like all living things cannabis also requires fuel to grow. A good friable soil mix that is rich with compost, living organisms, vitamins and minerals can supply your plants with enough food for their whole life cycle.